|
 | ||
Bio-Hydraulic & R&O FluidsBio-Ultimax™ Hydraulic Fluids AW 1000 & 2000 (ISO 32, 46, 68)Bio-Hydraulic Fluids, Bio-Ultimax™ 1000 & 2000, are ultimately biodegradable vegetable based formulas that replace mineral oil based hydraulic fluids. Bio-Ultimax™ Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. Bio-Ultimax™ Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and have shown to have exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 2OVQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882), Vickers 1-286-5, pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150° to 210° F. The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524, and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. Bio-Ultimax™ AW 1000 meets and exceeds Federal Specifications A-A-59354 Superseding MIL-H-46001D. The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity. The HOBS's extremely low
volatility increases the flash and fire safety features in the formula. They are formulated to provide seal conditioning for longer seal life and to reduce oil
leakage from the system. Bio-Ultimax™ Hydraulic Fluids should be used in hydraulic systems where low toxicity, and BIODEGRADABILITY properties are required.
Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. Bio-Ultimax™ 1000 - Navy ASDS Hydraulic Fluid (ISO 32)The test data below show the Bio-Ultimax™ 1000 Hydraulic Fluid typical specifications and actual bench tests performed by independent laboratories. These tests were performed in combination by Petro-Lubricant Testing Laboratories, Inc., the Lubrizol Corporation, and Chevron Phillips Chemical. The requirement for the hydraulic fluid involved an P9290 off gassing test for toxicity and replacement for MIL-PRF-l 7672D & Amd. 32075 T.H. (Grade 32) that is currently used as the outboard hydraulic oil for the submarines. This is identified as a highly critical area for the military. Patented Product: US Patent6,383,992, US Patent 6,534,454 with additional Pending and Foreign Patents. Bio-Ultimax™ Hydraulic Fluid AW 1000 (SAE 10W40)A specially formulated, ultimately biodegradable product designed for hydraulic driven systems that require a heavier SAE 40 viscosity for summer and fluid that passes the winter 10W viscosity for cold temperature pumpability protection (i.e.: approved by Hustler Mower Engineering for this OEM specifications). Bio-Ultimax™ Hydraulic Fluid is formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties. It is highly inhibited against moisture and rusting in both fresh and sea water and passes both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formula). A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements. Bio-Ultimax™ Hydraulic Fluid is designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and has shown exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 2OVQ, 3SVQ-25 (M-2950-S), and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 1500 to 2100 F. The anti-wear performance exceeds the load stage 10 in the FZG (DIN 5 1354) requirements for US Steel 136, DIN 51524, and GM (LS-2). It also meets the requirements for ashless GL-3 gear oils in reduction units and gear sets where it meets the viscosity range. The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity. The HOBS's extremely low
volatility increases the flash and fire safety features in the formula. It is formulated to provide seal conditioning for longer seal life and to reduce oil
leakage from the system. Bio-Ultimax™ Hydraulic Fluid should be used in hydraulic systems where low toxicity and BIODEGRADABILITY properties are required.
Base oils and additives in this product pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and wildlife Service and the US EPA. Bio-Ultimax™ 1200LT Hydraulic FluidsBio-Ultimax™ I200LT (Low Temperature) Hydraulic Fluids are ultimately biodegradable, biobased formulas that were designed specifically to replace mineral
oil based hydraulic fluids for environmentally sensitive and/or cold temperature areas, Bio-Ultimax™ 1200LT Hydraulic Fluids are formulated to perform in
hydraulic systems that require anti-wear, anti- foam, anti—rust, anti—oxidation, and demulsibility properties. They are highly inhibited against moisture and
rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the
Stabilized High Oleic Base Stocks (HOBS) into the formula, gives multi-grade synthetic base oil performance by boosting the viscosity index (VI) past synthetic
levels (energy conserving formulas). This super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load
capacity. They provide additional fluid value at the higher temperatures, which is a performance benefit over lower VI products of the same ISO viscosity.
The HOBS's extremely low volatility increases the flash and fire safety features in the formula compared to petroleum formulations with the same viscosity ranges.
A zinc-free additive system has also been developed that is environmentally friendly and exceeds the load stage 10 in the FZG (DIN51354) requirements for low
viscosity hydraulic and turbine oils. They may be used in reduction gears for cold temperature applications, where the OEM recommends a lighter viscosity or
SAE 0W for proper channeling. Bio-Ultimax™ 1500 Dielectric Hydraulic Fluids AW (ISO 22, 32, 46, 68)A specially formulated, ultimately biodegradable product designed specifically for use in hydraulic equipment operating over a wide range of temperatures and where an oil with high dielectric (>35 KV) insulating property is required. Applications include power utility aerial lift buckets, mobile and stationary hydraulic systems, or other equipment where electrical insulating safety is preferred. Bio-Ultimax 1500 Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and passes both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). A zinc- free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements. Bio-Ultimax™ 1500 Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and has shown exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882), Vickers I-286-S, pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 1500 to 210° F. The anti-wear performance exceeds the load stage 10 in the FZG (DIN 51354) requirements for US Steel 136, DIN 51524, and GM (LS 2) It also meets the requirements for ashless GL-3 gear oils in reduction units and gear sets where it meets the viscosity range. The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity. The HOBS's extremely
low volatility increases the flash and fire safety features in the formula. It is formulated to provide seal conditioning for longer seal life and to reduce oil
leakage from the system. Bio-Ultimax™ 1500 Hydraulic Fluids should be used in hydraulic systems where low toxicity, and BIODEGRADABILITY properties are
required. Base oils and additives in this product pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. Bio-HVO™ Hydraulic Fluid (ISO 46 & 68 FR Fluids)Bio-HVO™ Hydraulic Fluids are ultimately biodegradable vegetable based formulas that meet and exceed Vickers M2950-S, Vickers 1-286-5, U.S. Steel 126, U.S. Steel 127, and U.S. Steel 136. They have been USDA Biobased tested to show new carbon (vegetable oil) at > 96% and they are Specially formulated to offer the lowest toxicity in aquatic conditions. They are an excellent choice for inner plant applications (ie. Steel Mills) as fire resistant (FR) hydraulic fluids, with exceptional oxidation stability (RBOT 350-400 minutes) exceeding US Steel minimum requirement of 120 minutes. Although they have a pour point of -25°C, care must be taken if used in hydraulic systems setting static below 0°C for extended periods. Bio-HVO™ Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear, Anti-Rust, and Anti-Oxidation properties. There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10. They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized High Oleic Base Stocks (HOBS) into the formulas, gives multi-grade synthetic base oils performance by boosting the viscosity index to synthetic levels (Energy Conserving Formulas) A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements. The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formulas and their load capacity. The HOBS's extremely low volatility increases the flash and fire safety features in these formulas. (Can be listed by Factory Mutual as less hazardous fluids) Bio-HVO™ Hydraulic vegetable based fluids should be used where improved oxidation stability, excellent anti-wear performance, low toxicity, and
BIODEGRADABILITY properties are required. Bio-HVO2™ Hydraulic Fluid (ISO 46 & 68 FR Fluids)Bio-HVO2™ Hydraulic Fluids are ultimately biodegradable vegetable based formulas that meet and exceed Vickers M-2950-S, Vickers 1-286-5, U.S. Steel 126, U.S. Steel 127, and U.S. Steel 136. They have been USDA Biobased tested to show new carbon (vegetable oil) at>96% and they are Specially formulated to offer the lowest toxicity in aquatic conditions. They are an excellent choice for inner plant applications (ie. Steel Mills) as fire resistant (FR) hydraulic fluids, with improved oxidation stability (RBOT 200-250 minutes) exceeding US Steel minimum requirement of 120 minutes. Although they have pour points of -25°C and -30°C, care must be taken if used in hydraulic systems setting static below -10°C for extended periods. Bio-HVO2™ Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear, Anti-Rust, and Anti-Oxidation properties. There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10, They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilizedl High Oleic Base Stocks (HOBS) into the formulas, gives multi-grade synthetic base oil performance by boosting the viscosity index to synthetic levels (Energy Conserving Formulas). Bio-HVO2™ Hydraulic Fluids are designed to meet ISO grade viscosity requirements, and the multi-grade performance may allow one hydraulic fluid to replace two or more ISO grade products and reduce inventory. A zinc- free additive system has also been developed that is environmentally friendly and meets or exceeds Vickers and Denison pump performance. The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and load capacity. The HOBS's extremely low volatility increases the flash and fire safety features in these formulas. (Can be listed by Factor Mutual as less hazardous fluids) Bio-HVO2™ Hydraulic vegetable based fluids should be used where low temperature properties, improved oxidation stability, excellent anti-wear performance,
low toxicity, and BIODEGRADABILITY properties are required. Bio-Hydraulic™ Fluids (ISO 32, 46, 68)Bio-Hydraulic™ Fluids are ultimately biodegradable vegetable based formulas that meet and exceed Vickers M-2950-S, Vickers 1-286-5, U.S. Steel 126, and U.S. Steel 127. Bio-Hydraulic™ Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties. There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10. They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. Bio-Hydraulic™ Fluids are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity. The HOBS's extremely low
volatility increases the flash and fire safety features in the formula. They are formulated to provide seal conditioning for longer seal life and to reduce oil
leakage from the system. Bio-Hydraulic Fluids should be used in hydraulic systems where low toxicity and BIODEGRADABILITY properties are required. Bio-Hydraulic
Fluids are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. We believe Earths environmental future rests in
the use of renewable materials. Bio-MIL-PRF-32073 Hydraulic Fluid (ISO 15, 22, 32, 46, 68)Bio-MIL-PRF-32073 Hydraulic Fluids are ultimately biodegradable vegetable biobased formulas that were designed specifically to replace mineral oil based
hydraulic fluids for environmentally sensitive areas. They have been specifically formulated to provide additional seal swell (10% to 30%) as required by
MIL-PRF-32073 and ISO 15 or ISO 22 can replace obsolete specification MIL-PRF-5606 for ground support equipment. Bio-MIL-PRF-32073 Hydraulic Fluids are formulated
to perform in hydraulic systems that require anti-wear, anti-foam, anti-rust, anti-oxidation, and demulsibility properties. They are highly inhibited against
moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity
index of the Stabilized High Oleic Base Stocks (HOBS) into the formula, gives multi-grade synthetic base oil performance by boosting the viscosity index to
synthetic levels. This super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity.
The HOBS's extremely low volatility increases the flash and fire safety features in the formula. A zinc-free additive system has also been developed that is
environmentally friendly and exceeds the load stage 10 in the FZG (DIN51354) requirements for both turbine oils and reduction gears. They also meet the
requirements for an ashless GL-3 gear oil. Bio-AW/AL™ Hydraulic Press Oils (ISO 32, 46, 68)Bio-AW/AL™ Hydraulic Press Oils are ultimately biodegradable vegetable based formulas that replace mineral oil based hydraulic fluids in demanding press hydraulic systems. Bio-AW/AL™ Hydraulic Press Oils are formulated to perform in hydraulic systems that require Anti-Wear (AW), Anti-Leak (AL), anti-rust, anti-oxidation, anti-foam, and demulsibility properties. Bio-AW/AL™ Hydraulic Press Oils contain the same performance benefits and additive technology as the Bio-Ultimax™ 1000 Hydraulic Fluids with the addition of the anti-leak and/or non-drip performance. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). A zinc-free (ashless) additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements. Bio-AW/AL™ Hydraulic Press Oils are designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps when used in accordance with the equipment manufacturer. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 2OVQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150° to 210° F. The anti- wear performance exceeds the load stage 10 in the FZG (DIN 51354) requirements for US Steel 136, DIN 51524, and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity. The HOBS's extremely low
volatility increases the flash and fire safety features in the formula. They are formulated to provide seal conditioning for longer seal life and to reduce oil
leakage from the system. Bio-AW/AL™ Hydraulic Press Oils should be used in hydraulic systems where low toxicity, and BIODEGRADABIL1TY properties are required.
Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. Bio-AW Turbine™ R & O Fluids (ISO 32, 46, 68, 100, 220)Bio-AW Turbine™ R & O Fluids are ultimately biodegradable vegetable based formulas that were designed specifically to replace mineral oil based turbine
oils in environmentally sensitive hydroelectric (water) turbine bearings. These bearings are subject to humid/ moist conditions because of occasional seal leakage,
but operate cooler than gas and steam turbine bearings. Bio-AW Turbine™ Fluids are formulated to perform in R & 0 systems that require anti-foam, anti-rust,
anti-oxidation, and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of
the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized° High Oleic Base Stocks (HOBS) into the formula, gives
multi-grade synthetic base oil performance by boosting the viscosity index to synthetic levels, This super high viscosity index of the HOBS naturally improves the
thermal shear stability of the formula and increases load capacity. The HOBS's extremely low volatility increases the flash and fire safety features in the formula.
A zinc-free additive system has also been developed that is environmentally friendly and exceeds the load stage 10 in the FZG (DIN5 1354) requirements for both
turbine oils and reduction gears. They also meet the requirements for an ashless GL-3 gear oil. Bio-Synthetic™ Trans-Hydraulic (Universal Tractor Fluid)Bio-Synthetic™ Trans-Hydraulic is a universal tractor fluid that incorporates Stabilizedt additive technology with biodegradable vegetable based stocks. This formulation contains special frictional modifiers for the Wet Brake's equipment design, and is compounded with detergent, dispersant, anti-wear, anti-rust, and anti-foam inhibitors. This Bio-Synthetic™ Trans-Hydraulic Fluid is an ultimately biodegradable, multi-grade lubricant that can be used in agricultural, industrial, and construction equipment and has proven field performance. Meets or exceeds the requirements of John Deere's Quatrol and Hygard (Specification J20-C); Allison C-3, Cat TO-2 and API GL-4, Low-Speed/High Torque.
Passes: J20-C/M1139 High Torque Axle, Wet Brake Chatter/Squawk, PTO Clutch and the North America Performance Requirements for Universal Tractor Transmission Oils
(UTTOs). Bio-Synthetic™ Hydrostatic Fluid (Low-Viscosity) Universal Tractor FluidBio-Synthetic™ Hydrostatic Fluid is a universal tractor fluid that incorporates Stabilized additive technology with biodegradable vegetable based stocks. This formulation contains special frictional modifiers for the Wet Brake's equipment design, and is compounded with detergent, dispersant, anti-wear, anti-rust, and anti-foam inhibitors. This Bio-Synthetic™ Hydrostatic Fluid is an ultimately biodegradable, multi-grade lubricant that can be used in agricultural, industrial, and construction equipment where low viscosity and improved cold- temperature performance is required. Meets or exceeds the requirements of Massey-Ferguson M-1110, Ford-New Holland M2C41-B, Case-IH MS 1210 and John Deere's Low Viscosity Hygard
(Specification J20-D; Improved-water tolerance, anti-foam, thermal stability and reduced brake chatter), Approved or Recommended in Allison C-3 and Cat TO-2.
Meets or exceeds 150-32 Hydraulic and API GL-4 gear requirements for low viscosity fluid applications. BioBased products are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. BioBased products have exceptional benefits over petroleum-based lubricants because there is no direct danger of polluting the air, water, soil, or work environment through the loss of the lubricant. Other advantages include: biobased, biodegradable, renewable, low toxicity, no hazardous volatile organic compounds (VOC), more fire resistant, safer, EPA and ISO 14000 compliant and high OSHA and worker acceptance. |
|||
| Home | Contact Us | About Us | |||
 |
Your Link to BioBased Lubricants |
| 1-866-929-9556 |
